Arc-Type Tungsten Carbide Drawing Dies Introduction

Tungsten carbide drawing dies mold core work area is rendered "arc-type" and thus make metal tungsten carbide drawing dies mold core deformation in the region even more tortuous flow leads to unnecessary additional shear deformation and deformation work increased so that the drawing stress in general than the "straight" Carbide drawing dies mold core work area increases by 10 to 30%, but "straight" Carbide drawing dies mold core work area each contour line the slope is the same point so that when we determined the optimum cone half-angle α workspace when you can pull the metal with minimal stress and drawing "arc-type" Carbide drawing dies due to the curvature of each point of its contour line different and therefore can not make the whole Carbide drawing dies mold core work area there is an optimal workspace cone half-angle α.

YSN3D Tungsten Carbide Drawing Dies Introduction

YSN3D tungsten carbide drawing dies are non-magnetic alloy is mainly applied to the magnetic mold making industry. YSN3D Carbide drawing dies hardness of not less than 87HRA. 13.9g/mm ³ density range into the 14.9g/mm ³, bending strength is about 1900MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YL10.2 Tungsten Carbide Drawing Dies Introduction

YL10.2 tungsten carbide drawing dies major role in the diameter is less than the range of 1.5 ~ 10mm steel, tungsten, molybdenum wire drawing speed and other hard materials and surface finish drawing demanding non-ferrous metal pipe (line) drawing materials, hardness of not less than 1600HW3 (92.0HRA). Density is about 14.5g/cm ³, bending strength is about 4000 kgf / mm ². Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

YG20D Tungsten Carbide Drawing Dies Introduction

YG20D tungsten carbide drawing dies mainly used in the manufacture of standard parts, carbide cold-bearings, tools, and other industries use, cold warheads and bullet molds and stamping molds. Hardness of not less than 82HRA, 13.4g/mm ³ density within the range of 13.8 g / mm ³, and the flexural strength of about 2300MPa, all the holes have a certain shape in the center, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YG20C Tungsten Carbide Drawing Dies Introduction

Flexural strength YG20C tungsten carbide drawing dies is probably 2480MPa, and TL40.5 tungsten carbide drawing dies as primarily for the manufacture of standard parts, carbide industry with the cold-bearings, tools, molds and warheads and cold shells stamping molds. Hardness of not less than 82HRA. Density Carbide drawing dies YG20C in 13.4g/mm ³ into 13.8g/mm ³ range. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

YG15 Tungsten Carbide Drawing Dies Introduction

YG15 tungsten carbide drawing dies mainly used in the production of steel bars and steel tensile drawn under high compression ratio and anvil, perforation and punching tools work under greater pressure, hardness of not less than 87HRA. Density is about 14g/mm³, bending strength is about 2800MPa. Has a strong compressive pressure can be used. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YG10 Tungsten Carbide Drawing Dies Introduction

Have a certain shape hole YG10 tungsten carbide drawing dies all centers, round, square, octagonal, or other special shapes, and YG8 tungsten carbide drawing dies as mainly suitable for the production of steel and non-ferrous metal rod and drawn tubing drawing dies. Hardness of not less than 88.5HRA, density is about 14.5g/mm³, a bending strength of about 2400MPa. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YG8 Tungsten Carbide Drawing Dies Introduction

YG8 tungsten carbide drawing dies mainly suitable role in the production of drawn steel and nonferrous metal rod and tube drawing dies, the hardness of not less than 89.5HRA. Density is probably 14.8g/mm ³, bending strength of about 2200MPa. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. Has a certain shape of the center of all holes, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YG6 Tungsten Carbide Drawing Dies Introduction

YG6 tungsten carbide drawing dies mainly suitable for the production of less than ¢ 20.00mm bore drawing of non-ferrous metal rod and the hole is less than ¢ 10.00mm pipe die hardness of not less than 90.5HRA. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Density is about 14.95g/mm ³, bending strength is about 1900MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

YG6X Tungsten Carbide Drawing Dies Introduction

YG6X tungsten carbide drawing dies excellent corrosion resistance and wear performance, mainly suitable for the production of less than ¢ 6.00mm bore drawing drawing dies. Hardness of not less than 91.5HRA, density is about 14.95g/mm ³. Flexural strength is about 1800MPa, the center of all holes have a certain shape, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. There are a variety of sizes are available for selection, cost savings, poor conditions applicable to the use of brushed occasions.

YG3 Tungsten Carbide Drawing Dies Introduction

Intensity of use YG3 tungsten carbide drawing dies and moderate impact toughness, wear resistance slightly higher than YG3X Carbide drawing dies. Drawing die not under stress conditions is mainly applied to the drawn diameter <3mm steel, non-ferrous metals and their alloys wire or wire rod. Hardness of not less than 91HRA, 15.0g/mm ³ density range into the 15.3g/mm ³, bending strength is about 1200MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

YG3X Tungsten Carbide Drawing Dies Introduction

Tungsten carbide drawing dies YG3X high hardness, good wear resistance but low strength, impact toughness poor are not drawing die under stress conditions. Mainly used in drawing the diameter of <2mm thin steel, non-ferrous metals and their alloys wire filament. Hardness of not less than 91.5HRA, 15.0g/mm ³ density range into the 15.3g/mm ³, bending strength is about 1100MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

YB20C Tungsten Carbide Drawing Dies Introduction

YB20C tungsten carbide drawing dies suitable role in the production of stamping dies, density 3.4g/mm ³ into 13.8g/mm ³ range. Mainly used carbide bearings, carbide tools, carbide standard parts such as cold heading and cold industry and warheads and shells stamping, hardness of not less than 83.5HRA. Flexural strength of about 2480MPa, all centers have a certain shape of the hole, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity and a low coefficient of friction.

TL40.5 Tungsten Carbide Drawing Dies Introduction

TL40.5 tungsten carbide drawing dies hardness of not less than 81HRA, mainly used in the manufacture of standard parts, carbide industry with cold red bearings, tools, molds and warheads and shells cold stamping molds. Density of 13.0 g / mm ³ to 13.6 g / mm ³, bending strength is about 2480MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

JL50 Tungsten Carbide Drawing Dies Introduction

JL50 tungsten carbide drawing dies and YG20 Carbide drawing dies as primarily for the manufacture of stamping dies, such as stamping watch parts, strings and other musical instruments, red battery shell mold toothpaste, small balls, screws and other stamping dies. Hardness of not less than 85HRA. Density 13.8g/mm ³ to 14.2 g / mm ³, bending strength is about 2300MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

Hy10 Carbide Drawing Dies Introduction

Hy10 tungsten carbide drawing dies mainly used in the production of drawn steel bars and steel high tensile and compression ratio under the anvil, perforation and punching tools work under greater pressure, hardness of not less than 87.5HRA. The density 14.1g/mm ³ to 14.5 g / mm ³ range, bending strength is about 2060MPa. Have a certain shape of the hole all centers, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics. Excellent corrosion resistance and wear performance, a variety of sizes available for selection and cost savings.

HK12 Tungsten Carbide Drawing Dies Introduction

HK12 tungsten carbide drawing dies hardness of not less than 87.5HRA, YG15 Carbide drawing dies with the same principal applies to the production of drawn steel bars and steel stretching under high compression ratio and anvil under greater pressure of work, perforation and stamping tools. Density of 12.4 g / mm ³ to the 12.7g/mm ³ range, bending strength is about 2100MPa. All centers have a certain drawing die shaped hole, round, square, octagonal, or other special shapes. Has a strong compressive pressure can be used. Carbide brittle nature, can not guarantee that it does not break. Therefore, extreme caution when handling. As a high-quality carbide core, with high hardness, good thermal conductivity, low coefficient of friction characteristics.

How selection the tungsten carbide drawing dies fitting?

Although wiredrawing mode can be used for processing all kinds of steel, copper, tungsten, molybdenum etc metal and alloy material of different materials, but drawing die each have its applicable machining scope, therefore drawing mould material is rational selection of key to ensure successful application to obtain the longest die longevity. Different material wiredrawing molds all have its relatively reasonable processing object.

According to the material drawing mode can be divided into alloy steel, hard alloy mould, natural diamond die, polycrystalline diamond mold, CVD diamond die and ceramic mold and so on many kinds. And widely used in electronic devices, radar, television, instruments and aerospace and other high-tech industries, with strong abrasion resistance, service life is extremely high.

Tungsten Carbide Drawing Dies Introduction

Tungsten carbide is a class of materials widely used in drawing dies because of their superior strength, toughness and wear resistance. All major wire producers can use drawing dies, which include wire drawing dies, tube drawing dies, bar drawing dies. Available in varied bore sizes, the range of tungsten carbide drawing dies that we bring forth is used in drawing wires, bars and tubes of different materials. The tungsten carbide drawing dies fitting that we manufacture, export as well as supply are widely demanded in the global market. These are fabricated with tungsten carbide blanks and are used for drawing wires, bars and tubes. Also, these are available with bore sizes from 0. 2 MM to 120.000 MM along with varied case sizes.